Semiconductor Heater HG 140 Series 15W to 150W
●Pressure clamp connectors
●Dynamic heating up
●Wide voltage range
●Temperature limiting
●Energy saving
●Clip fixing
●Quick installation
These heaters are used in enclosures where damage from condensation must be prevented，or where the temperature may not fall below a minimum value.The aluminium profile heater body design has a chimney effect and distributes the heat evenly.The pressure clamp connectors save time and simplify installation
| Technical Data | |
| Operating voltage | 120-240VAC/DC’(min.110V，max.265V) |
| Heating element | PTC resistance, automatic adjustment, limit temperature |
| Heater body | Extruded aluminium profile，anodised |
| Connection | 3 pressure clamps for stranded wire 0.5- 1.5mm(with wire end ferrule)and rigid wire 0.5-2 .5mm |
| Connection casing | Plastic according to UL94V-0, black for UL94V-0 black plastic |
| Mounting | Clip for 35mm DIN rail, EN 50022 |
| FiRing position | Vertically |
| Operating/Storage temperature | -45 to+70℃(-49 to+158°F) |
| Protection typelProtection class | IP20/l(earthed) |
*Operating with voltages below 140V AC/DC reduces heating performance by approx.10%
Related products
-
SK3110.000 Series of Electronic Thermostat
Inner temperature controller for switchgear cabinet Especially used for controlling fan filter，heater and exchanger.also could be monitoring the electric cabinetinner temperature when working as signal arcuser. Technical Data Make bimetal sensor as heat sensitivity set to feedback of heat. Contact point scheme:single switch over contact point as instant switch component allowed load of contact point KL5-3 ACI0（4）A DC=30WKL5-4（Cooling） AC5（4）DA DC=30W （D）=s...
-
Three-Phase Voltage And Current Combination Tab...
Overview The three-phase voltage and current combination meter is a multi-functional electrical measuring instrument with programmable measurement, display and digital communication functions. It can complete electricity measurement, data display, acquisition and transmission, and can be widely used in substation automation, distribution automation, intelligent buildings , Electric energy measurement, management and assessment within the enterprise. The measurement accuracy is 0.5 level, and ...
-
SG-6000 Series of Mechanical Thermostat
Introduction The RTC70.xx iS used for 2-position contr01 with on/off output for the control the temperature by means of an NTC sensor placed externally or internally in the thermostat.the thermostat acquires the room temperatu re with its built-in sensor or floor sensor.and the heating contact will close when the room temperatu re falls below the selected setpoint. Application For the control of warm-water（floor）heating systems and direct electric heating systems u...
-
Intelligent lighting control module
Overview The appearance of this product is a plastic shell, and it uses a grid shell to facilitate internal heat dissipation: it is equipped with a standard 35mm nickname phase guide rail groove, which is easy to install and can realize lighting control or curtain control for 4/8/12/16 channels, etc. The current of each circuit can reach 0-20A: when the current of the controlled light or electrical equipment is greater than 20A, it can be connected to a relay or a co...
-
Tamperproof Thermostats(pre-set)FTO 011/FTS 011
●Small size ●Default temperature settings ●Easy to install ●High switching tolerance Tamperproof（Pre-set）Thermostat FTO 011 Contact breaker/NC（red casing）for regulating heaters or for switching signal devices when temperature has fallen below the minimum value.The contact opens Wnen temperatu re is rlslna. Tamperproof（Pre-set）Thermostat FTS 011 Conact maker/NO（blue casing）for regulating filter fans，heat exchange rs，cooling devices or for switching signal de...
-
Fire power supply
Basic skills The voltage/current signal sensor can collect the voltage and current value of the detection circuit at the same time, or only collect a certain circuit or a few channels according to actual requirements. It can be networked with the fire-fighting equipment power monitoring host, and the monitoring host can judge the status of the on-site sensor. Status, after the host computer analyzes and processes, it indicates the type of a circuit fault alarm, and sends out an audible and vi...
